Peninsula College plans to build a reactor

Discuss the technical details of an "open source" community-driven design of a polywell reactor.

Moderators: tonybarry, MSimon

Post Reply
MSimon
Posts: 14334
Joined: Mon Jul 16, 2007 7:37 pm
Location: Rockford, Illinois
Contact:

Peninsula College plans to build a reactor

Post by MSimon »

http://iecfusiontech.blogspot.com/2007/ ... pdate.html

I'm going to post Devon's request here. The best place to reply (for now) would be at the above link since it will give Devon an automatic notification.
Hi my name is Devon and I am a student at Peninsula College. I am currently a part of an undergraduate research project where we are attempting to build and IEC. At the moment we are trying to decide what level of vacuum pump we need for our fusor. I am looking through the books you offered in your blog but was hoping you could tell me how you came to a decision on a level of vacuum. Our advisor would like for us to prove mathematically what level we need.
Thanks for your help,
Devon
Here is a link to the Peninsula College's home page:

http://pc.ctc.edu/

*

JohnP
Posts: 296
Joined: Mon Jul 09, 2007 3:29 am
Location: Chicago

Post by JohnP »

They probably want to check on http://www.fusor.net/

drmike
Posts: 825
Joined: Sat Jul 14, 2007 11:54 pm
Contact:

Post by drmike »

I tried to reply to this some where, but I can't find it now. Basicly I pointed out that you need to compute the density of particles from air and the density you need for fusion reactions. If you keep the ratio of the components of air constant (not how pumps really work, but close enough for a homework problem) then you can get the number density of particles you can live with.

Computing pumping speeds is another problem. Also fun, but different.

MSimon
Posts: 14334
Joined: Mon Jul 16, 2007 7:37 pm
Location: Rockford, Illinois
Contact:

Post by MSimon »

The number density of particles you can live with is dependent on Paschen discharge.

Dr. B. says the maximum is 1E-6 torr.

You want the density to be as high as possible in order to maximize fusion.

Turbo pumps are rated in l/s pumping speed which for practical purposes in the region of interest is constant and independent of pressure.

So what you want to figure also is the input flow rate required to keep the pressure constant.

There is also the compression ratio problem. Turbo pumps have a compression ratio for H2 on the order of 1,000. So you need two pumps in series to get the outlet pressure up into the backing pump range (1 torr).

http://iecfusiontech.blogspot.com/2007/ ... mping.html

http://iecfusiontech.blogspot.com/2007/ ... esign.html

http://iecfusiontech.blogspot.com/2007/ ... tings.html

http://iecfusiontech.blogspot.com/2007/ ... uages.html

http://iecfusiontech.blogspot.com/2007/ ... izing.html

http://iecfusiontech.blogspot.com/2007/ ... alves.html

http://iecfusiontech.blogspot.com/2007/ ... meter.html

http://iecfusiontech.blogspot.com/2007/ ... -shut.html
Engineering is the art of making what you want from what you can get at a profit.

classicpenny
Posts: 106
Joined: Thu Feb 14, 2008 5:50 pm
Location: Port Angeles WA USA
Contact:

Fusion at Peninsula

Post by classicpenny »

Derek Madison, one of the students involved in the Peninsula College Fusor Project reported to me in a voice mail that they achieved fusion on Jun 21. He says they will attempt to duplicate the results today Jun 23 at 10:30 AM in the Peninsula Physics lab.

classicpenny
Posts: 106
Joined: Thu Feb 14, 2008 5:50 pm
Location: Port Angeles WA USA
Contact:

Fusion at Peninsula College 2

Post by classicpenny »

Here are the Peninsula College students who made fusion on Jun 21, and again today on Jun 23. They detected their neutrons with a bubble detector purchased from Dr Derrico of Yale Univ (Yale will only sell their bubble detectors to other educational institutions.) Today I saw at least three bubbles appear in the gel in the little vial, after an exposure of about 1 minute at a distance of about 0.1 m from the chamber wall. Left to right: Devon (who originally contacted MSimon), Ivan, Sarah, Chris, Aaron, and Derek. They can be contacted through their advisor, Jeff Zirul: jeffz at pcadmin dot ctc dot edu.
Image
Here is the vacuum chamber.
Image
And here is the discharge glow.
Image
I did my best to resolve the bubbles in the gel - but bad lighting and limited resolution got the best of me.
Bill Flint

Roger
Posts: 788
Joined: Fri Jul 06, 2007 2:03 am
Location: Metro NY

Post by Roger »

Very cool, congrats to all.
I like the p-B11 resonance peak at 50 KV acceleration. In2 years we'll know.

MSimon
Posts: 14334
Joined: Mon Jul 16, 2007 7:37 pm
Location: Rockford, Illinois
Contact:

Post by MSimon »

Outstanding. Kudos to all.
Engineering is the art of making what you want from what you can get at a profit.

drmike
Posts: 825
Joined: Sat Jul 14, 2007 11:54 pm
Contact:

Post by drmike »

That's great! Congratulations to everyone. That's a lot of work.

Now I really want a welder!!
:D

JohnP
Posts: 296
Joined: Mon Jul 09, 2007 3:29 am
Location: Chicago

Post by JohnP »

Really nice job. I've been trying to get something put together here at Northeastern Illinois University from bits & pieces we already have...

WillKell
Posts: 17
Joined: Thu May 29, 2008 4:50 pm
Location: Dallas,TX
Contact:

Too cool

Post by WillKell »

Congrats and Saludos!

MSimon
Posts: 14334
Joined: Mon Jul 16, 2007 7:37 pm
Location: Rockford, Illinois
Contact:

Post by MSimon »

I blogged it at all the usual places with pictures: thanks ClassicPenny.

They sent me a nice thank you.

Simon
Engineering is the art of making what you want from what you can get at a profit.

tombo
Posts: 334
Joined: Fri May 09, 2008 1:10 am
Location: Washington USA

Post by tombo »

You Rock!
When you turn up the voltage tell me so I can sell my neighbors in Friday Harbor lead underwear!
-Tom Boydston-
"If we knew what we were doing, it wouldn’t be called research, would it?" ~Albert Einstein

classicpenny
Posts: 106
Joined: Thu Feb 14, 2008 5:50 pm
Location: Port Angeles WA USA
Contact:

Finally Made the Local Paper

Post by classicpenny »

Well well. Finally made the local paper.

http://www.peninsuladailynews.com/artic ... /807030302

Post Reply